|
|
 
   Sanitron� Ultraviolet Water
Purifiers
|
 |
|
|
Sanitron�
Monitoring Options
Guardian�,
Sentry�,
Steralert Sheet� |
 The
STERALERT� lamp status alarm
monitors visible light emitted through
the sight port plug of the water
purifier and activates an audible alarm
when visible light falls below
acceptable levels.
� Easy installation, no tools
� Mounts on the sight port plug
� Warns of lamp or power failure
� Produces a high frequency tone pulse
at two to three cycles per second
� Monitors visible light only; does not
monitor ultraviolet intensity
� Operates on a 9v battery or optional
120v 60Hz Power Adapter,
specify when
ordering
� Available for use with all models
Steralert 30-0035
Steralert 30-0061
Steralert 30-0085
Steralert 30-0090
 The SENTRY� safety sensor
provides constant monitoring of
the water purifier's ballast and
germicidal lamp operation; indicator
lights provide constant visual indication of
ballast and germicidal lamp status.
� Easy installation,
� Plug SENTRY� into an electrical
outlet, then plug water purifier into SENTRY�
� Operates optional Solenoid Valve and
Audio Alarm
� Warns of lamp failure
� Easily adaptable for use with other
water purifier brands.
� Available in 120v 50/60 Hz or 220-240v
50/60 Hz
� Available for use with all models
Sentry� Manual |
 The GUARDIAN� Ultraviolet Monitor
visually indicates the level of
germicidal ultraviolet energy that
penetrates the quartz sleeve and the
water within the disinfection chamber.
The GUARDIAN� Ultraviolet Monitor
is capable of operating an optional
Audio Alarm and Solenoid Valve. In
addition, the GUARDIAN�
Ultraviolet Monitor will detect loss of
ultraviolet due to lamp outage,
component or power failure. Use of the
Ultraviolet Monitor is recommended by
the US Public Health Service "Criteria
for the Acceptability of an Ultraviolet
Disinfection Unit".
The GUARDIAN� Ultraviolet Monitor
will detect reduction of ultraviolet
levels due to:
1. Fouling or deposits on quartz sleeve.
2. Poor ultraviolet transmission through
the water. (Color, Turbidity, organic or
other impurities in the water can reduce
or interfere with the transmission of
ultraviolet rays.)
3. Depreciation of lamp output due to
usage or other cause. (Lamp output
gradually depreciates with use. Lamp
replacement is recommended once each
year.)
The GUARDIAN� Ultraviolet Monitor
has three models; Analog, Digital and
Digital Remote. Voltage Configurations
include 120V / 50 or 60Hz, 220-240V / 50
or 60 Hz, or 12VDC. Contact factory for
special requirements. NOTE: GUARDIAN�
Ultraviolet Monitor (analog, digital or
digital remote) can be purchased and
installed with the water purifier or at
a later date for an existing
installation.
The GUARDIAN� Ultraviolet Analog
and Digital Monitors are mounted
directly on to the water purifier. The
sensor probe (included) is threaded into
the sight port fitting of the
ultraviolet water purifier. The aluminum
collar on the bottom of the GUARDIAN�
Ultraviolet Analog or Digital Monitor is
secured over the sensor probe.
The GUARDIAN� Ultraviolet Digital
Remote Monitor is intended for use in a
location away from the water purifier
that is being monitored. In all other
respects, the remote GUARDIAN�
behaves the same as the standard
GUARDIAN�. Mounted on the back of
the remote monitor is a socket into
which the lead from an ultraviolet
sensor is connected. Instead of being
mounted inside the monitor housing, this
sensor is contained within the remote
probe. A standard length for the
connecting cable supplied with the probe
is 50 ft., but the lead length may be
extended if desired. Please contact the
factory for additional lengths.
Guardian� Manual |
|
|
Sanitron�
Water Purifiers are
manufactured under
patents owned by the
Atlantic Ultraviolet
Corporation. Made in the
USA. Copyright MCMLXXII,
MCMXCI, MCMXCVII
Sanitron�
is a registered
trademarks of the
Atlantic Ultraviolet
Corporation
Ster-L-Ray�
and Easy-Off�
Retainer Cap are
trademarks of the
Atlantic Ultraviolet
Corp. |
|
|
|
